Products

SALE

110dB High Output 5V Alarm Buzzer with LED Lights

Sold Out

Louder than most standard buzzer's operating at 85dB, this buzzer is super loud at an approximate 110dB output, along with 4 programmable LED lights it is indispensable for locating your lost quad or alerting you of any error. Specifications: Voltage 5V LED 4pcs x WS2812 (programmable thru Betaflight) Size 27mm x 14mm x 11mm Connection flight controller buzzer output Weight 2.9g Mounting 3M mounting...

SALE

Airbot Furling32 MINI 45A– F3 BLHELI 32 ESC

~~SGD$27.00~~ SGD$18.90

A powerful ESC in a small package, the Furling32 Mini is the latest ESC from Airbot and employs a full F3 onboard MCU operating at 108Mhz compared to most other Blheli32 ESCs running F0 MCU at 48Mhz. This latest F3 ESC gives a smooth control and fast response and supports up to 50amp burst and 45amp continuous. With the higher...

SALE

Alpha A85 Body Frame (Replacement Frame + Canopy)

~~SGD$25.00~~ SGD$15.00

Alpha A85 Turtle 800TVL with FrSky R-XSR

Sold Out

The iFlight Alpha series features the Turtle 800TVL Camera attached to one of iFlight's new 2inch whoop frames. An ideal combination of flight time efficiency with sufficient power, optimal balance between weight and power. Specifications : Wheelbase 85mm Body size 125*125mm Prop 2 inch FC pattern 25.5*25.5mm AIO board FPV cam spacing 14mm Lipo 3 - 4S Weight 76.4g (without...

Annoying Self Powered 110dB Alarm Buzzer

SGD$8.75

Warning : This buzzer is ANNOYINGLY LOUD. Connected and configured like the usual lost model buzzer that is powered by the main battery. In the event of main battery disconnection in a crash, this self powered buzzer will be activated automatically, making it easier to locate your quad with it's super loud 110dB output buzzer. Operation: In normal operation with the main battery...

SALE

Backpack buckle (Flight bag Accessory)

~~SGD$6.80~~ SGD$4.08

Made to maximize your existing flight bag, strap your quadcopters on the outside of your backpack and save the internal space for other equipment. Features : Lightweight, stylish carbon fibre plate and TPU brackets. Easy to install, only 3 holes will be needed to mount on your backpack. Package include 1 pc x Buckle Mount Set, 1 pc x 20*200mm straps 1...

SALE

Battery Protection Plate

~~SGD$6.20~~ SGD$3.10

A complete battery retention kit for racing frames with bottom mounted batteries, it comes with non-slip silica gel pad mounted on carbon fibre plate to keep the battery in place during flight and provides protection when landing. Specifications : Material 3K high strength carbon fibre board Thickness 1.5mm Anti Slip Pad Silicone gel pad with self adhesive Size 42 x...

Battery Silicone Anti-Slip Pad

SGD$0.60

These anti-slip battery pads provide grip surface between the battery pack and frame, prevent slippage of LiPo battery mid-flight. To keep the pad contact surface tacky, rinse with water or wipe with a wet cloth. Available in two sizes. Specifications: Material Soft silicone Colour Black Size 65mm x 25mm x 1mm, 100mm x 30mm x 2mm Mounting 3M self-adhesive on...

Bonka U2 SI GR 1300mAh 6s 100c Silicone Graphene Lipo Pack

Sold Out

*Not available for overseas shipment A new upgraded version of BONKA FPV performance U2 batteries series, employing the latest Silicone Graphene (SI GR) composition for added consistent explosive power - Ultralight - Higher reliability - Remarkable performance Specifications: Cells 6S Capacity 1300mAh Discharge 100C (130amp) Nominal Voltage 22.2V Cell Configuration 6S1P Connection XT60 plug Dimension W50mm x H34mm x L75mm Weight 240g * For those in the know and seek...

SALE

Bonka U2 SI GR 1500mAh 4s 95c Silicone Graphene Lipo Pack

~~SGD$44.20~~ SGD$23.85

*Not available for overseas shipment A new upgraded version of BONKA FPV performance U2 batteries series, employing the latest Silicone Graphene (SI GR) composition for added consistent explosive power - Ultralight - Higher reliability - Remarkable performance Specifications: Cells 4S Capacity 1500mAh Discharge 95C (142.5amp) Burst Discharge 190C (285amp) Nominal Voltage 14.8V Cell Configuration 4S1P Connection XT60 plug Dimension W37mm x H34mm x L76mm Weight 196g * For those in the...

BrotherHobby Speed Shield 2207.5 2400kV/2700kV Racing Motor - 1 piece / A set of 4

SGD$24.98

Special price for package orders! Click drop down box for pricing! Speed Shield, the latest high performance motor from BrotherHobby, is one of the most colorful racing motors around. This motor has an unique stator size of 2207.5 at the weight and size of a smaller motor, giving you the edge in the race to the finish line! Specifications: Stator 2207.5...

DALProp 7" Fold 2 F7 Folding DIY Props Long Range

SGD$5.60

Features:Folding design for more durability, easier transportation and fold on impactPOPO CompatibleSuper smooth and high efficiency with no vibration Specifications: Pitch 5.1 Size 7 inch Blade Tri Weight 7 g Hub Thickness 7 mm Package 4 x Hubs and 12 x Blades (2 x CW + 2 x CCW) Color Crystal Red Material PC

DALProp Cyclone T5050C

SGD$2.80

Designed for high speeds while managing the efficiency and noise profile, DALProp T5050C Tri-Blades is the latest release in the popular DAL cyclone series. They are specifically engineered to improve control at low and high speeds with more thrust. It's excellent aerodynamics design features faster reaction, making it best for drone racing. Specifications: Pitch 5.0 Size 5 inch Blade Tri Package 4 props...

EWRF e7082TM 5.8G 48CH Adjustable Power FPV Mini VTx with OSD & Smart Audio Support

SGD$13.65

The EWRC e7082TM mini FPV VTx is features packed with 48channel, wide input DC voltage range and selectable transmitting power of 25mW, 100mW, 200 mW and Pitmode (Off); this VTx will fit most flying requirements. Click here for a DVR flight video (by Vincent from Team DGK) with this VTX fitted with a dipole antenna Pitmode reduces transmitting range to <2m allowing you to power...

EWRF e708TM3 5.8G 48CH Adjustable Power FPV VTx with OSD & Smart Audio Support

SGD$13.86

The EWRC e708TM3 FPV VTx is features packed with 48 channels, wide input DC voltage range and selectable transmitting power of 25mW, 200mW, 600 mW and PITmode (Off); this VTx will fit most flying requirements. PITmode reduces transmitting range to <2m allowing you to power your craft for pit work without interfering with other flyers in the air. The Betaflight...

SALE

EWRF e7092TM (UWA) 5.8G 48CH 0/25/100/200mW FPV Mini VTx with OSD & Smart Audio compatibility Support

~~SGD$17.20~~ SGD$12.04

The EWRF e7092TM FPV video transmitter is a features packed 48channel mini VTx with wide input DC voltage range and selectable transmitting power of 25mW, 100mW, 200 mW and Pitmode (Off); this VTx will fit most flying requirements. Pitmode reduces transmitting range to <2m allowing you to power your craft for pit work without interfering with other flyers in...

SALE

EWRF e709TM3 (MMCX) 5.8G 48CH Adjustable Power FPV VTx with OSD & Smart Audio support

~~SGD$25.50~~ SGD$17.85

The EWRC e709TM3 FPV video transmitter is a feature packed 48channel VTx with wide input DC voltage range and selectable transmitting power of 25mW, 200mW, 600 mW and Pitmode (Off); this VTx will fit most flying requirements. Clean powerup reduces interfering with other flyers Pitmode reduces transmitting range to <2m allowing you to power your craft for pit work...

SALE

EWRF e709TM3 Pro (with Mic) 5.8G 48CH 25mW 200mW 500mW FPV VTx with OSD and Smart Audio support

~~SGD$27.00~~ SGD$18.90

The EWRF e709TM3 PRO edition features packed video transmitter now fitted with a built in microphone ; a 48channel VTx with wide input DC voltage range and selectable transmitting power of 25mW, 200mW, 500 mW and Pitmode (Off), new PCB design with breakoff tabs for smaller and tighter frames, this VTx will fit most flying requirements. Clean powerup reduces interfering with...

Extension Cable - SMA Female to uFL IPEX

Sold Out

SALE

FatShark Goggles Straps Black

~~SGD$8.30~~ SGD$4.98

SALE

Foxeer Echo Patch 5.8G Antenna 8DBi SMA

~~SGD$26.50~~ SGD$18.55

Patch antenna for FPV goggles. Specifications : Colour Red Shell material PC+ ABS Weight 8g Length 21.7mm Connector SMA Type Directional Polarisation RHCP Gain 8dBi Impedance 50 ohms Axial ratio < 3 Bandwidth 5.5 to 6.0 GHz Centre frequency 5.8 GHz Radiation angle 84.7 degrees Package include 1pc x Foxeer Echo Patch Antenna 1pc x 45 degree SMA adapter ...

Foxeer Lollipop 3 2.5DBi 5.8G Stubby Antenna, SMA (2pcs)

SGD$16.94

Tiny light weight stubby antenna, designed for FPV racing. Updated version with unibody and alloy copper material for better signal and gain Specifications : Colour Red, White Shell material PC+ ABS Weight 4.8g Length 22.7mm Connector SMA Type Omnidirectional Polarisation RHCP Gain 2.5dBi Axial Ratio < 1 Bandwidth 5.5 to 6.0 GHz Centre Frequency 5750MHz Radiation Efficiency 98% Package include...

Foxeer Lollipop 3 2.5DBi 5.8G Super Mini Extended Antenna, SMA/RP-SMA (2pcs)

SGD$16.73

Tiny light weight antenna, designed for FPV racing. Updated version with unibody and alloy copper material for better signal and gain Specifications : Colour Purple, Red, Black, Florescent Green Shell material PC+ ABS Weight 7.3g Length 60mm Connector SMA Type Omnidirectional Polarisation RHCP Gain 2.5dBi Axial Ratio < 3db Bandwidth 5.5 to 6.0 GHz Centre Frequency 5750MHz Radiation Efficiency 98%...

Foxeer Razer Micro FPV Camera - 1.8mm IR Blocked

Sold Out

The Razer is an all new micro FPV camera from Foxeer with 1200TVL, low latency and good low light performance 1200TVL definition with advanced natural image. Advanced quality 1.8mm M8 lens. 4:3/16:9 optional, PAL/NTSC switchable. Supports 4.5~25V input voltage. Specifications: Sensor Type CMOS 1/3 Scale 4:3 / 16: 9 Optional TV System PAL/ NTSC Switchable Resolution 1200TVL FOV 4:3 FOV-H...

FPV Camera TPU Protection Cage V2 (KATAK STRETCH - SE & TRP V2)

SGD$3.90

New improved, completely re-designed as a 2 pieces component for increased durability and lower replacement cost. This FPV camera cage provides protection against those camera smashing frontal crashes. 3D printed from TPU for increased durability and in attractive colours. Fit both KATAK Stretch SE as well as the TRP V2 and will fit camera’s with Gopro style lens. Specifications:...

SALE

FPV Package

Sold Out

FPV Package which features RUSH VTx, Foxeer Razer Micro Camera and Foxeer Antenna at a special price! Click on the product title below for more product details: Note: All Foxeer Lollipop Antenna comes with random colour. Package 1 : -Rush TANK VTx 5.8G 48CH 0/25/500/800mW -Foxeer Razer Micro FPV Camera - 1.8mm IR Blocked -Foxeer Lollipop 3 2.5DBi 5.8G Stubby Antenna,...

SALE

FPV Racing Pro Airgate by Total Rotor - Large

~~SGD$67.60~~ SGD$47.32

Total Rotor Pro Airgates for FPV racing are designed to be portable and easy setups. Feature foldable tough fiber glass frame with stainless steel end spikes. Brightly printed flag fabricated from heavy duty fabric and reinforced stitches at critical points to increase durability. Come with ropes and stainless steel end spikes for anchoring in windy conditions. New clean design...

SALE

FrSky Ultra Mini Receiver R-XSR

~~SGD$38.00~~ SGD$26.60

FrSky ultra mini receiver R-XSR is the evolution of FrSky full range XSR receiver. The R-XSR is a standalone receiver with all the functions of XSR, in addition, it’s almost 1/3 size and 1/3 weight of XSR receiver. Moreover, there redundancy function is integrated into this tiny receiver ensures the security, and the IPEX connector makes it more convenient for you...

SALE

FULLSEND 3S 450mAh 75C - XT30

~~SGD$14.16~~ SGD$8.50

The FULLSEND 3S 450mAh 75C Lipo Battery is lightweight and very compact size. . The Lipo fits into the iFlight CineBee whoop and TurboBee whoop. This battery increases flight time significantly and it also provides a little more power over the stock battery. Features : * Advanced battery technology doubles your device's performance time* High discharge performance and high energy...

SALE

FULLSEND 4S 450mAh 75C - XT30

Sold Out

The compact and lightweight design of FULLSEND 4S 450mAh 75C Lipo Batteries makes it ideal for H frames and 4S whoop drones. Features: * Advanced battery technology doubles your craft's performance time* High discharge performance*Lithium Polymer raw materials from Japan and Korea * Reliable power for FPV micro H-frame quads and whoop quads Specifications: Minimum Capacity 450mAh Discharge Rate 75C Configuration...

Gemfan Flash Triblade 2540-3 (8pcs)

SGD$3.64

(Price is for a set of 8 props) Micro quad triblade propellers from GemFan, compatible with 1.5mm motor shaft or M2 screws two-hole mounting. Specifications: Pitch 4.0 Size 2.5 inch Blade Tri Material PC Hub Size 5mm Weight 0.7g/pc Motors 1105, 1106 Package 8 props (4 x CW + 4 x CCW) Colours Clear, Clear Blue, Yellow, Red

SALE

Gemfan Flash Triblade 4052-3 (4pcs)

~~SGD$4.00~~ SGD$2.80

(Price is for a set of 4 props) Micro quad triblade propellers from GemFan, compatible with 18 - 22 series motors. Specifications: Pitch 5.2 Size 4.0 inch Blade Tri Material PC Hub Size 7.5mm Weight 3.85g Motors 18 - 22 series motor Package 4 props (2 x CW + 2 x CCW) Color Clear Purple

Gemfan Hulkie Triblade 2040-3 (8pcs)

SGD$3.01

(Price is for a set of 8 props) Micro quad triblade propellers from GemFan, compatible with 1.5mm motor shaft or M2 screws two-hole mounting. Specifications: Pitch 4.0 Size 2 inch Blade Tri Material PC Hub Size 5mm Weight 0.78g/pc Motors 0806-1105 Package 8 props (4 x CW + 4 x CCW) Colours Clear, Clear Blue

GEPRC GEP-HX2 Hummingbird (3mm version)

Sold Out

The Hummingbird is a small bird, fast and agile; exhibiting the characteristics of this amazing bird, the GEP-HX2 Hummingbird micro racing frame features a True-X configuration with a 110mm wheelbase for 2 inch props, FPV camera protection plate and 3K carbon fibre parts. Total Rotor’s GEP-HX2 version comes with 3mm main board plate for strength and stiffness, further enhancing...

GEPRC GR1105 - 5000KV Motor

Sold Out

GEPRC SPEEDX GR1105 5000KV 2-4S FPV Racing Brushless Motor for RC Drone Features: * N52H magnet ensures high temperature resistance and low loss of magnetic field * Japanese NSK bearings, ensure smooth operation of motor * Lightweight base design for efficient heat dissipation Specifications: Operating KV 5000Kv No. of cells (LiPo) 2-4S Configuration 9N12P Stator Length 1.9mm Shaft Diameter 1.5mm Motor dimensions...

SALE

GEPRC GR1204 - 5000KV Motor

Sold Out

GR1204 Racing Motor, Whoop and Toothpick Class Features: * High efficiency * Designed for Toothpick or Whoop Drone building * Dual bearing design and balanced bell for smoother operation * Compatible with 40mm-75mm propellers Specifications: Operating KV 5000Kv No. of cells (LiPo) 3-4S Configuration 9N12P Stator 1204 Shaft Diameter Ø1.5mm Motor Dimensions Ø15.28 x 10.9mm Rotor N52H arc magnets Base Casing 7075-T6 Weight 3.8g...

SALE

HGLRC DinoShot 60A BlHeli 32 4 in 1 ESC

~~SGD$99.80~~ SGD$69.86

Full size high capacity 4 in 1 esc from HGLRC with high quality MosFets and more than 30 on-board ceramic capacitors for noise reduction. Compatible with most FC but designed to be pair with HGLRC standalone FC the AIRBUS Features: 32bit FO51K86 MCU,48mHz running speed; N-Channel Mosfets 33pieces Low ESR capacitors, total capacity 880uf, lower ripple and more stable voltage;...

HGLRC Hornet 120mm Micro Frame (2.5 inch prop)

Sold Out

The Hornet is a 2.5 inch racing quad with minimalist design for speed and agility. Simplicity in build, clean in form, light in weight, and exciting in flight. Specifications : Wheelbase 120mm Frame type Unibody Material Carbon Fiber Thickness 3mm Frame weight 20g Flight controller mount 20 x 20mm (recommended HGLRC F4 micro stack) Motor size 11 series motor...

SALE

HGLRC T-Rex 35AMP BLHeli_32 bit ESCs

Sold Out

HGLRC T-Rex ESCs feature high quality Japanese Toshiba MOSFETs and Japanese Murata Ceramic Capacitors. The 3oz High-TG PCB board reduces heat soak and improves system efficiency. Ultra-small footprint and ultra-light, complete with silicon wires. Specifications: Firmware BLHeli_32 Protocol DSHOT1200 / DSHOT600 / 300 / 150 / Oneshot125 / 42 / MultiShot ESC telemetry Yes MCU STM32F051 MOS N FET, Toshiba...

High-Grip Reusable Battery Pad

Sold Out

These battery pads provide excellent grip between the battery pack and frame, prevent slippage of LiPo battery mid-flight. To keep the pad contact surface tacky, rinse with water or wipe with a wet cloth. Specifications : Material PU based Gel Colour Clear Size 50mm x 50mm x thickness 3mm Note use scissors to cut to size before peeling the clear protective...

SALE

HQ Durable Prop T2X2X4 (4pcs/set)

~~SGD$4.00~~ SGD$2.80

SALE

iFlight 5.8GHz Micro Antenna (uFL)

Sold Out

Upgrade for micro stack with dipole antenna. Direct replacement for iFlight Alpha Whoop A85 quad Specifications : Colour Black Length 75mm Connector uFL Polarisation RHCP Frequency range 5.8GHz Package include : 1pc x 5.8GHz FPV Antenna

SALE

iFlight Battery Handbag

~~SGD$11.00~~ SGD$6.60

Flexible combination: Change the space combination, storage 4 DJI Spark batteries / 3 Dji Mavic Pro Batteries/ 2 Dji Phantom3/4 batteries.Safeguard lipo battery: This flame retardant bag is a convenient way of safeguarding your lipo batteries during charging, transit, and storage.Always remember to comply with charging and safety guidelines and never leave charging or damaged Lipo batteries unattended. Features : - Intensive...

iFlight Foldable Field Chair

Sold Out

Light, compact and foldable flight chair. Individual leg height adjustment for various seat angle to cater to different needs. Specifications : Weight 0.9kg Size 25.5"(H) x 20"(W) x 20" (D) Height Adjustment 3 steps Color Black with red trims Max Weight Capacity 100kg Package includes 1 x chair frame, 1 x canvas seat, 1 x storage pouch

SALE

iFlight iON Drive 2205 2500KV FPV Motor (Set of 2 motors)

~~SGD$39.50~~ SGD$29.63

The iON motors offering incredible power, efficiency, and torque; is an all-new series designed from the ground up by iFlight. Committed to performance and efficiency, these new motors features the best materials for durability. The bell and base are milled from 7075 aviation grade aluminium with unique counter-sunk heat dissipation vent holes in the bell, and the titanium alloy...

iFlight SucceX Mini F4 Fly Tower V2

Sold Out

SucceX 2-6S Mini F4 Fly Tower is specially suited for micro racers. One of the first mini stack with 6S LiPo capabilities, it is also for those looking to reduce weight on their mini sized quad. The stack include the SucceX mini F4 flight controller, SucceX 35A 4-in-1 ESC and 48 channels multi power VTx, fit directly on frames with...

iFlight Tachyon T1108 5000KV Micro FPV Racing Motor (set of 2 motors)

Sold Out

Specially made for 2 to 3inch propellers, perfect on micro class FPV quads; iFlight is committed to providing high performance and efficient products to all our customers and is proud to introduce the all new Tachyon Series motors that is designed from the ground up. Offering incredible power, efficiency, and torque, Tachyon Motors underwent extensive and rough testing to ensure...

SALE

iFlight Tachyon T2207 2650KV FPV Racing Motor

~~SGD$25.00~~ SGD$17.18

iFlight is committed to providing high performance and efficient products to all our customers and is proud to introduce the all new Tachyon Series motors that is designed from the ground up. Durability is a high concern for us since we understand crashing quadcopters at high speed happens and for this reason the Tachyon series motor are made only with the...

SALE

iFlight Tachyon T2306 2650KV FPV Racing Motor

~~SGD$25.00~~ SGD$17.55

iFlight is committed to providing high performance and efficient products to all our customers and is proud to introduce the all new Tachyon Series motors that is designed from the ground up. Durability is a high concern for us since we understand crashing quadcopters at high speed happens and for this reason the Tachyon series motor are made only with the...

iFlight XING X2207 2450KV/ 2750KV FPV NextGen Motor

SGD$21.83

iFlight XING series motors, designed by FPV pilot and specialist Patrick Xing; combining iFlight's high-quality motor production technology with Patrick Xing's technical expertise to produce a top-of-the-line motor. The elliptical body, powerful stator with high temperature resistant windings, N52H magnets, very small air gap and dynamically balanced bell; result in a motor that delivers incredibly smooth power and thrust. These amazing looking XING motors...

iFlight XING X2306 2450/2750KV FPV NextGen Motor

SGD$21.83

iFlight XING series motors, designed by FPV pilot and specialist Patrick Xing; combining iFlight's high-quality motor production technology with Patrick Xing's technical expertise to produce a top-of-the-line motor. The elliptical body, powerful stator with high temperature resistant windings, N52H magnets, very small air gap and dynamically balanced bell; result in a motor that delivers incredibly smooth power and thrust. These amazing looking XING...

SALE

Infinity RS Force V3 1550mAh 4s Square LiPo (120 - 240C)

~~SGD$47.30~~ SGD$22.70

Special price for package orders! Click drop down box for pricing! *Not available for overseas shipment Infinity Force with graphene tech, version 3 of the successful RS Force racing batteries; featuring a higher discharge platform than version 2 as well as lower sag and higher reliability compared to other similar products. Square form factor will fit most frames and reduces the risk of damage...

iPeaka BORG 35A BLHeli 32 bit ESC 4-in-1 DSHOT 1200

SGD$78.00

iPeaka BORG 35A BLHeli 32 is designed with 32 bit 48MHz FO51K86 MCU, complete with 33 pieces of low ESR capacitors for noise control. It ensures fast response, smooth and stable control of the motors while providing a smooth flight experience and absolute control. The optional heatsink effectively pulls heat away from the MOS tubes, protecting the critical parts of your...

SALE

iPeaka Mini 35A BLHeli 32 bit ESC DSHOT 1200 (A set of 4)

~~SGD$91.50~~ SGD$64.05

The BLHeli_32 bit ESC brings the speed advantage of 32 bit and functionality to quadcopter FPV racing. The mini form size allows the mounting on frames with skinny arms. When paired with the iFlight Revo Bee32 F4 Pro flight controller, an even cleaner and weight shaving is achieved. The advantage: 32 bit processors operate faster than 8 bit, at which...

SALE

Jumper R1D16 Receiver

~~SGD$20.30~~ SGD$14.21

The Jumper R1D16 receiver is compatible with all devices capable of using FrSky D16 mode. Specifications: Dimension 20*15*4mm (without antenna) Weight <2g Number of channels 16ch (SBUS) RSSI (Signal Strength Indication) output 0-3.3v Data return S.port Operating Voltage Range 4.0~6V Operating Current Range 80mA@5V Effective distance full distance (>1.5km) Compatibility FrSky D16 Mode Binding method:Press and hold the receiver's...

Jumper T16 Gimbal Stick-ends Upgrade (M3 thread)

Sold Out

Jumper T16 Internal Multi-Protocol Radio Module Upgrade

Sold Out

Kit to convert Jumper transmitters (T16 and T16 Plus) with external radio modules to internal based radio module as in the Jumper T16 Pro transmitter. The conversion leaves the external JR bay free for use with modules such as CRSF Click link here for installation guide

Jumper T16 Pro V2 (Hall Sensor Gimbals)

Sold Out

The Jumper T16 Pro V2 now comes with an external battery charging port utilizing USB Type C and folding handle for increased convenience along with the same amazing features of the Pro V1; such as full colour screen, new hall sensor gimbals, internal multi-protocol radio module and external JR module bay for use with an external TBS Crossfire module. Jumper T16 is...

SALE

Jumper T18 Pro Carbon Faceplate (ALPS RDC90 Gimbals)

~~SGD$265.50~~ SGD$225.00

The Jumper T18 Pro version comes with the super smooth ALPS RDC90 sensor gimbals offering higher precision than Hall sensors. The Jumper T18, operating on OpenTX, brings the best features of the T16 series along with an upgrade of the JP4-in-1 module into JP5-in-1 for more compatibility The Jumper T18 has a JP5-in-1 multi-protocol module with 2.4G JP4-in-1 and 915MHZ / 868MHZ at...

SALE

Leopard GEP-LX4-V4

~~SGD$64.20~~ SGD$38.52

Leopard are natural predators, capable of staggering acceleration and speed. Manufactured with 3k ultra-light carbon fibre and #7075 aviation aluminum parts for a rigid platform, the Leopard's exhibits great flight characteristics and yet tough against crashes. The V4 Leopard while retaining the quality of the original, it features a striking colour scheme in blue camouflage. All key frame parts...

SALE

M5 Low Profile Motor Props Locknut

~~SGD$4.20~~ SGD$2.10

Low profile to reduce the risk of props working loosely; especially when using props with thicker hubs or motors with shorter shaft. Specifications: Size M5 Material Alloy Colour Titanium grey Profile Low Type Self locking Package includes 4 x locknuts

Micro Cameras Adapter with Protection Cage TPU (KATAK STRETCH - SE & TRP V2)

SGD$3.90

Designed specifically for mounting the light weight Runcam Micro series of FPV camera on the Katak Stretch SE and TRP V2 frame. This FPV camera adapter also provides protection against those camera smashing frontal crashes. 3D printed from TPU for increased durability and in attractive colours. Fit both KATAK Stretch SE as well as the TRP V2. Comes in two...

Micro FPV Camera Adapter (KATAK STRETCH - SE & TRP V2)

SGD$2.10

Shed up to 10g by using these adapters to mount a micro FPV camera on your KATAK Stretch SE or the TRP V2 frames. Easy to mount and designed to allow multiple camera height to suit your preference with no additional screws or nuts required. Specifications: Material TPU Colour Orange, Purple, Red Camera angle 80 degrees Weight 1.8g each pair ...

Mini 5.8G FPV VTx Whip Antenna - MMCX

SGD$1.55

Simple lightweight whip antenna, great for short range FPV flying or close proximity flying on mini quads where antenna "catch" is more likely to happen. Also tested indoor and car park flying conditions with good results. Specifications: Frequency 5.8hz range Connector MMX Angle / Straight Length 8.2cm (tip to connector tip) Weight with connector Angle: 1.5g Straight: 1.5g

SALE

Mini 5.8G FPV VTx Whip Antenna - SMA

~~SGD$3.10~~ SGD$2.17

Simple lightweight whip antenna, great for short range FPV flying or close proximity flying on mini quads where antenna "catch" is more likely to happen. Also tested indoor and car park flying conditions with good results. Specifications: Frequency 5.8hz range Connector SMA Male Length 110mm (tip to connector tip) Weight 5.5g with connector

SALE

Mini 5.8G FPV VTx Whip Antenna - uFL IPEX

~~SGD$1.80~~ SGD$1.26

Simple lightweight whip antenna, great for short range FPV flying or close proximity flying on mini quads where antenna "catch" is more likely to happen. Also tested indoor and car park flying conditions with good results. Original replacement part for EWRF e7092TM VTx Specifications: Frequency 5.8hz range Connector uFL IPEX Length 65mm (tip to connector tip) Weight 1g with...

MMCX to SMA Pigtail Replacement for EWRF e709TM3

SGD$1.60

SALE

Motors screw set (20pcs)

~~SGD$4.70~~ SGD$2.82

SALE

Panda Power 1300 4S 95c Top C Series

~~SGD$36.70~~ SGD$22.02

*Not available for overseas shipment Awesome new pack from Bonka! These packs take the beating, even from the more abusive setups like 2206-2600s and 5051x3 props! Specifications : Capacity 1300mAh Type 4S1P / 14.8V / 4 cell lithium polymer Constant discharge 95C Burst discharge 190C Charge Rate 1-3C recommended, 5C max Power Connector XT60 Size 33 x 34 x...

SALE

Replacement Arm for Vertigo VX2 Frame (2 pcs)

~~SGD$14.60~~ SGD$8.76

Replacement Motormount for Vertigo VX2 frame (2pcs)

SGD$3.75

SALE

Replacement Sponge for FatShark Goggles Faceplate

~~SGD$13.20~~ SGD$7.92

Improved comfort with the nylon sponge material and special nose bridge design reduces light leakage for pilots with smaller nose bridge. Specifications: Fit HD and Dominator series Attachment Velcro Material Nylon sponge Package includes 1 x grey foam 1 x black foam 2 x backing velcro

SALE

RGB 10 LED 3535 Multi-Colors Race Wire for 4 in 1 ESCs - 4pcs

Sold Out

iFlight's latest race wire for use with 4in1 ESCs motor connection can now be configured via the FC's firmware configuration, allowing multi-colored LED and scheme. Using race wires with 4in1 ESCs reduces the risk of cutting motor wires from prop strikes. It is also great for mounting underarm for lighting up your quad. Specifications: Current capacity 40amps No. of...

SALE

RPSMA Male to SMA Female Extension/ Adapter cable

~~SGD$4.00~~ SGD$2.00

Rubber Vibration Damping Bobbins for Flight Controllers - M2/ M3

SGD$2.10

With the high cycle timing of current flight controllers and powerful motors employed by FPV quad racers, soft mounted flight controllers are almost always required to prevent twitches or oscillations caused by high-frequency vibrations that interfere with accurate gyro reading and PID tunes. These bobbins uses soft but tough rubber damping material to damp out motors, props train and frame's undesirable...

RunCam Micro Swift 2 - 2.1mm IR Blocked

Sold Out

Specifications: Image Sensor 1/3" SONY Super HAD II CCD Horizontal Resolution 600TVL Lens 2.1mm (M8) FOV160° IR Blocked Signal System PAL / NTSC Integrated OSD Yes One Touch Scene Setting(AGC) Personal / Lightrax / Outdoor / Indoor / Cloudy / Twilight S/N Ratio >60dB (AGC OFF) Electronic Shutter Speed PAL: 1/50~100,000; NTSC: 1/60~100,000 Auto Gain Control (AGC) Yes Min....

SALE

RunCam Micro Swift 3 V2 – 2.1mm IR Blocked

~~SGD$45.80~~ SGD$34.35

Specifications: Image Sensor 1/3" SONY Super HAD II CCD Horizontal Resolution 600TVL Lens 2.1mm (M8) FOV160° Signal System PAL / NTSC Integrated OSD Yes One Touch Scene Setting(AGC) Personal / Lightrax / Outdoor / Indoor / Cloudy / Twilight S/N Ratio >60dB (AGC OFF) Electronic Shutter Speed PAL: 1/50~100,000; NTSC: 1/60~100,000 WAuto Gain Control (AGC) Yes Min. Illumination 0.01Lux@1.2F...

RunCam Racer 2 – 1.8mm/2.1mm IR Blocked

SGD$35.33

RunCam Racer 2, a micro size FPV camera designed specifically for FPV racing with ultra low latency of 6ms and super-WDR. The Racer 2 comes with an additional adapter for mounting in a full size frame Specifications: Model RunCam Racer 2 Image Sensor Super WDR CMOS Sensor Horizontal Resolution 700TVL Lens 1.8mm FOV160° / 2.1mm FOV 145° Screen Format 4:3...

RunCam Racer Nano 2 - 1.8mm IR Blocked

Sold Out

RunCam Racer Nano 2 is a micro size FPV camera designed specifically for FPV racing with ultra low latency of 6ms and super-WDR. The RunCam Racer Nano 2 has 3 pre-set scene mode: Personal, Lightrax and Darkness which can be changed via joystick control or gesture control. Specifications: Model RunCam Racer Nano 2 Image Sensor Super WDR CMOS Sensor Horizontal...

RunCam Swift 2 - 2.1mm IR Blocked

SGD$39.75

Specifications: Image Sensor 1/3" SONY Super HAD II CCD Horizontal Resolution 600TVL Lens 2.1mm IR Blocked Signal System PAL Integrated OSD YES Integrated MIC YES S/N Ratio >60dB(AGC OFF) Electronic Shutter Speed PAL:1/50~100,000; NTSC:1/60~100,000 AutoGain Control(AGC) YES Back light compensation(BLC) YES Min.illumination 0.01Lux/1.2F WDR D-WDR DNR 2DNR Day/Night Color / Auto / B&W Power DC 5 to 36V Working...

SALE

Rush Racing VTx- 5.8G 48CH Pit/25/50/200/500mW

~~SGD$34.30~~ SGD$24.01

RUSH Racing, a quality 5.8GHz VTX designed for racing quads with strong anti-interference ability and stable transmission. LOCK-ON technology prevents frequency drift, allowing up to 8 pilots to fly simultaneously without interference. Four adjustable levels of transmitting power -Pit/25/50/200/500/mW SmartAudio protocol authorized by TBS Full metal casing means efficient heat dissipation as well as great protection from crashes and dings...

SALE

Rush TANK VTx 5.8G 48CH Pit/25/200/500/800mW

~~SGD$44.70~~ SGD$31.29

RUSH Tank, a quality 5.8GHz VTX designed for racing or freestyle quads with strong anti-interference ability and stable transmission. LOCK-ON technology prevents frequency drift, allowing up to 8 pilots to fly simultaneously without interference. Four adjustable levels of transmitting power -Pit/25/200/500/800mW SmartAudio protocol authorized by TBS Full metal casing means efficient heat dissipation as well as great protection from crashes...

SANYO Electrolytic Capacitor Low ESR for Power Supply (pack of 2)

SGD$1.14

Available in 2 voltages - 25V and 35V Recommend for use on quads that experience issues caused by electrical “noise” in the system or FCs with sensitive gyros - lines in the FPV feed when increasing throttle, vibrations/oscillations that cannot be tuned out, motor glitches etc. Specifications: Rated voltage 35V (ideal for 4S LiPo, max 5S) 25V (ideal for 3S LiPo,...

SMA/ RP-SMA Adapter for Antenna

SGD$1.65

SMA/ RP-SMA Adapter- Extension cable

SGD$1.65

SALE

SpeedX GEP-GR1106 7500kv

Sold Out

GEP-GR1106, a high performance motor designed specifically by GEPRC for micro frames spinning 2 to 2.5” props. Ideal KV for 2S Lipos quads giving best balance of power and performance Specifications: Stator size 1106 Configuration 9N12P KV 7500 Shaft Dia 1.5mm Motor Size dia14.2mm x ht 14mm Rotor N50SH arc magnet Bearings NSK Voltage 2 - 3S Max Current...

SALE

Speedy Bee Bluetooth-USB Adapter

~~SGD$26.00~~ SGD$19.50

Speedy Bee Bluetooth-USB Adapter is an unique device that allows you to configure and tune your BetaFlight settings right from your phone via the SpeedyBee app which means no more lugging a laptop to the flying field! Specifications : Model Speedy Bee Bluetooth-USB Adapter Output power 0 dBm Receiver sensitivity -94 dBm Transmission rate Bidirectional 2K/s Bluetooth protocol Bluetooth specificiation V4.0...

Speedy Bee F7 AIO Flight Controller

Sold Out

Speedy Bee F7 AIO is an all new AIO flight controller that integrates PDB, Bluetooth , Barometer, 32MB OnBoard Flash for BlackBox, and users can adjust the parameters of the flight controller using the Speedy Bee App with an integrated Bluetooth chip. The board comes with esc solder pads for use with individual ESCs as well as a connector if building with...

SucceX 2-8S PDB w/ 5V/12V BEC

Sold Out

The Succex Power distribution board is designed for high voltage and high current applications. It consists of 2+2+3+3 layers of heavy copper to sustain maximum current demand. This PDB can sustain up to a maximum total 330A. Also features 12V 3Amp and 5V 3Amp regulators with a maximum of 8S (36V) input. In addition, it can also collect the signal...

SucceX 50A 2-6S 4-in-1 ESC

Sold Out

A high quality 30 x 30 full size BLHeli 32 ESC board with a good value to price performance, this ESC can handle input voltage of up to 6S and incorporate quality TDK MLCC low ESR capacitors and NTMFS5C430NL MOSFETs for good flight performance and response. Features: - 8 layers double-sided PCB board; - 4oz 1.6mm thick power board(0.9mm copper ratio),better...

SucceX 55A Slick 2-6S ESC (set of 4)

Sold Out

SucceX 55A Slick 2-6S ESC is specially designed for FPV racing frames with slim arms. The STM32F051 is combined with a high-performance 3 in1 driver for improved latency. Specifications : MCU STM32F051 Frequency Up to 48kHz PWM frequency Protocol Dshot1200, Proshot, Oneshot, Multishot Capacitance 470μF/50V Input 2-6S LiPo Current sensor Yes Capacity 35A, 45A burst Dimension 35*11mm Weight 3.7g without wires...

SucceX 60A V2 Plus BLHeli_32 4 in 1 ESC

Sold Out

iFlight SucceX 60A V2 Plus BLHeli_32 4 in 1 ESC is designed to give motors smooth power with great stability and durability. The 32bit 48mHz 3-IN 1 STM32F051 MCU, Metal MOSFET, TDK MLCC Low ESR ceramic capacitors provide high efficiency and better heat dissipation. A perfect companion to the SucceX TwinG F7 flight controller Specifications : MCU STM32F051 Protocol Dshot150/300/600/1200, Oneshot, Multishot...

SucceX F7 TwinG Flight Controller V2.1

Sold Out

SucceX F7 TwinG // GYRO FUSION is the NEXT-GEN flight controller, ready for anything, with 5 uarts, 8 motor outputs, 32Mb blackbox and a powerful F7 processor to run it all. With it's clean intuitive layout, the SucceX F7 TwinG makes installation a breeze with a 4-pin connector for your VTx and an 8-pin connector that allows simple plug and...

SALE

SucceX Force Nano 5.8g 300mW VTX Adjustable Power

~~SGD$39.00~~ SGD$27.30

Small in size but big in power! The iFlight Micro Force is the VTX you need for your next micro build. Excellent power output stability with switchable power from 25mW to 300mW and with a PIT mode. Original replacement part for iFlight Alpha Whoop A85 (NOTE: for replacement, reuse the VTX adapter board on the A85) Specifications : Power transmission PIT / 25...

SALE

SucceX Micro 200MW VTX

~~SGD$20.50~~ SGD$14.35

Replacement part for Succex Micro F4 V2.1 Flight Stack Specifications : Power PIT/25/100/200mW VTx control protocol IRC Tramp Antenna interface IPEX (UFL) Mounting holes 16 x 16mm Weight 1.6g Package include : 1 x 5.8G SucceX Micro 200mW VTX V2

SALE

SucceX Micro ESC 15A V2.1 with Plugs

~~SGD$49.50~~ SGD$34.65

Replacement part for Succex Micro F4 V2.1 Flight Stack Specifications : MCU BB21F16G BEC No Firmware G-H-30 BLS 16.7 BLHeliSuite http://www.mediafire.com/file/1tn449x6815upat/BLHeliSuite16714901.zip/file Input voltage 2-4S LIPO Continuous current 15A Current sensor Yes ESC protocol Pwm, oneshot125, multishot, dshot150, 300, 600, etc. Protocol support Smartaudio & Tramp VTX Mounting hole 16 x 16mm Weight 3.6g Package include : 1pc x SucceX...

Succex Micro F4 15A V2.1 Stack (plug motor connection )

Sold Out

SucceX 16x16mm micro F4 Tower is specially designed for micro (toothpick) FPV racing frame, compact and and stacked design in a small 16 x16mm form factor with the micro sized FC, ESC, and VTX neatly stack together with soft mount grommets. Highly integrated with all the latest features, optimized internal circuitry and pinned interconnects that makes for an easy straight...

SucceX Mini 35A 2-6S 4 in 1 ESC V2

Sold Out

Replacement ESC board for SucceX Mini F4 Stack. Specifications : Type V2 MCU STM32F051 Protocol Dshot1200, Proshot, Oneshot, Multishot Target iFlight-BL32-4IN1 Input 2-6S LiPo Current sensor Yes Capacity 35A, 45A burst Dimension 31 x 31mm (including the power pads) Mounting holes 20 x 20mm Package includes 1pc x SucceX Mini 35A 2-6S 4 in 1 ESC Click here for wiring diagram

SALE

SucceX-D Alpha Whoop F4 20A AIO Board

~~SGD$70.00~~ SGD$49.00

Original replacement part for iFlight Alpha Whoop Specifications : MCU STM32F411 Gyro MPU6000 Baro No Blackbox 8MB BEC output 5V 2A / 10V 2A INA pad nR2 Constant current 20A, 25A (Burst) Power input 2-5S (8-25V) Current Sensor Yes BLHeli BLHeli-S ESC Telemetry No Target IFLIGHT_F411_PRO ESC Firmware G-H-30 BLS Dimension 30.5 x 30.5mm Mounting pattern 25.5 x 25.5mm / φ3mm...

SucceX-D F7 TwinG Flight Controller V2.1 (HD Version)

Sold Out

The SucceX-D F7 V2.1 is designed to work seamlessly with DJI’s new HD FPV system, connector to allow direct connection of a DJI Air unit with the included wire harness. In addition, iFlight added the popular and reliable USB Type-C as used in the DJI module. *Features - Universal USB Type C connector instead of micro USB - Plug-and-Play. No need...

SALE

Super Micro LC Filter for FPV Video (2 packs)

~~SGD$2.30~~ SGD$1.73

Connected between power source (FC, PDB, BEC etc) and FPV components (VTx and FPV camera), LC filters can help to "clean up" dirty DC output jitters that causes lines in wireless video feed. This LC filter uses large value inductor and capacitor components for better filtering. Specifications: Max current 1A Max input voltage 4S Voltage 16V Size 10mm x...

SALE

T-Motor F40 III (2306-2400kV)

~~SGD$29.40~~ SGD$22.05

The F40 III F Series Motors, a new addition to T-Motor popular F Series with U5 design casing which minimizes dirt intrusion and improved cooling efficiency. Utilizing temperature resistant curved magnets, the version 3 guarantees stable output even at full throttle. The extended M5 motor shaft thread section with anti-slip prop seating allows for a wider choice of propellers....

T-Motor F40 PRO III - 2400KV/2600KV

SGD$28.88

Continuing the lineage, the F40 Pro III provides more thrust and increased durability compared to its predecessors. Each motor is supplied with high-quality EZO bearings for maximum performance and lifespan. On top of that, the overall stability of the motor has been enhanced with high-temperature resistance enameled silver-core windings which is able to withstand up to 240C. Lastly, the...

SALE

T-Motor F60 III (2207-2500kV)

~~SGD$30.70~~ SGD$23.03

The F60 III F Series Motors, a new addition to T-Motor popular F Series with U5 design casing which minimizes dirt intrusion and improved cooling efficiency. Utilizing temperature resistant curved magnets, the version 3 guarantees stable output even at full throttle. The extended M5 motor shaft thread section with anti-slip prop seating allows for a wider choice of propellers....

T-Motor F60 PRO III - 2500KV/2700KV

SGD$29.25

Continuing the success of their FPV racing motors, F60 Pro III is the latest from T-motor's stable of FPV racing motors promising higher thrust and durability. These new motors feature high temperature resistance (240 deg Celsius) enameled silver winding and titanium alloy motor shaft with stronger thread, riding on high quality EZO bearings. New great looking bell with anti-slip...

SALE

T-Motor FPV 30A 2-4S ESC

~~SGD$21.80~~ SGD$15.26

Mini ultra-light ESC designed for FPV Racing from T-Motor, running BLHeli-S firmware and state of the art MOSFETs for terrific response and efficiency. A perfect companion to the T-Motor F Series motors. Specifications : Continuous Current 30A Burst Current 40A No. of Cells (LiPo) 2-4S BEC No MCU EFM8bb21f16G Dimension 25.5 x 12.7 x 5 Weight with Wires...

T-Motor T5143S 3-blade Propeller

SGD$3.64

T5143S T-Motor Ultralight series prop, a lightweight and responsive tri-blade propeller. With its lightweight design, the prop comes in at only 4.1g. This low weight decreases spool up times, which increases feel and responsiveness. Absolutely perfect for lightweight builds or builds with higher KV motors that can take advantage of the lightweight design. The standout feature of this propeller is that...

T-Motor T5150 Props (10pcs)

SGD$7.63

(Price is for a set of 10 props) Go hard, go fast, with this durable and well balanced props from T-Motor, racing never feels better, experience excellent response and control through turns. Specifications: Pitch 5.0 Size 5.1 inch Blade Tri Material PC Hub thickness 7mm Mounting hole M5 (POPO Compatible) Weight 5.0g/pc Package 10 props (5 x CW + 5 x CCW)...

T16 Carbon Fiber Cover Replacement

Sold Out

Total Rotor Battery Strap (5pcs)

SGD$2.00

SALE

Total Rotor KATAK Stretch SE 5" FPV Racing Drone Frame Kit

~~SGD$62.40~~ SGD$37.44

Designed and produced by Total Rotor Singapore, the KATAK Stretch Special Edition is truly special having undergone extensive redesign from the standard edition. With new looks and features, all-round enhancements such as replaceable arms, high performance Mitsubishi carbon fibre; the Special Edition promises improved flight performance and durability for locked-in FPV race performance at an amazing price and quality of finish. Build...

SALE

Total Rotor KATAK Stretch SE Replacement Part - Arm

~~SGD$13.70~~ SGD$8.22

Original replacement parts for Total Rotor KATAK Stretch SE comprising of one arm. Arms are interchangeable between the 4 arms positions of the frame. Also available are TRP Racing Arms for a performance upgrade with a weight saving of 16-18 grams Compatibility : KATAK Stretch SE, TRP KATAK Stretch Build video: Click here Specifications: Material 4mm high performance Mitsubishi carbon...

SALE

Total Rotor KATAK Stretch SE Replacement Part - Bottom Plate

~~SGD$10.10~~ SGD$6.06

Original replacement parts for Total Rotor KATAK Stretch SE comprising of a bottom plate. Compatibility : KATAK Stretch SE, TRP KATAK Stretch Build video: Click here Specifications: Material 2mm high performance Mitsubishi carbon fibre Package 1 x bottom plate

SALE

Total Rotor KATAK Stretch SE Replacement Part - Middle Plate

~~SGD$10.10~~ SGD$6.06

Original replacement parts for Total Rotor KATAK Stretch SE comprising of a middle plate. Compatibility : KATAK Stretch SE, TRP KATAK Stretch Build video: Click here Specifications: Material 2mm high performance Mitsubishi carbon fibre Package 1 x middle plate

SALE

Total Rotor KATAK Stretch SE Replacement Part - Screws Set

~~SGD$8.50~~ SGD$5.10

Original replacement parts for Total Rotor KATAK Stretch SE comprising of a full set of hardware for one frame. All threads are M3. Compatability : KATAK Stretch SE, TRP KATAK Stretch Build video: Click here Specifications: 4pc Aluminium standoff M3 x 28mm (T) 8pcs YFS screw M3 x 12mm (B) 8pcs YFS screw M3 x 8mm (G) 4pcs...

SALE

Total Rotor KATAK Stretch SE Replacement Part - Side Plate Set

~~SGD$18.10~~ SGD$10.86

Original replacement parts for Total Rotor KATAK Stretch SE comprising of both side plates for the cage. Compatibility : KATAK Stretch SE, TRP KATAK Stretch, old version unibody of KATAK Stretch (Note: this version is NOT produced not sold by Total Rotor - requires 4 pcs of M3 x 8mm mounting screws. Some adjustments may be required.) Build video:...

SALE

Total Rotor KATAK Stretch SE Replacement Part - VTx Plate Set

~~SGD$4.10~~ SGD$2.46

Original replacement parts for Total Rotor KATAK Stretch SE comprising of a VTx plate and a SMA plate. Compatibility : KATAK Stretch SE side plates Build video: Click here Specifications: Material 2mm high performance Mitsubishi carbon fibre Package 1 x SMA plate, 1 x VTx plate

SALE

~~SGD$9.70~~ SGD$5.82

SALE

~~SGD$10.90~~ SGD$6.54

Sold Out

SGD$16.86

Lighter. Faster. Sleeker Original replacement parts for TRP SPRINT comprising of a pair / 2 pairs of racing arms. Specifications: Material 4mm high performance Mitsubishi carbon fibre Weight 13 grams Package 1 pair of opposing arms

SALE

~~SGD$9.90~~ SGD$5.94

Original replacement parts for TRP SPRINT comprising of a full set of hardware for one frame. All threads are M3. Specifications: 2pc Aluminium standoff M3 x 28mm (T) 2pc Aluminium standoff M3 x 20mm (T) 6pcs YFS screw M3 x 6mm (B) 2pcs YFS screw M3 x 8mm (B) 4pcs YFS screw M3 x 12mm (B) 4pcs YFS screw...

SALE

~~SGD$19.30~~ SGD$11.58

Lighter. Faster. Sleeker Original replacement parts for TRP SPRINT comprising of a side plate. Specifications: Material 2mm high performance Mitsubishi carbon fibre Package 1 x left plate, 1 x right plate Note except for the "TRP" logo, left and right plates are interchangeable

SALE

~~SGD$4.40~~ SGD$2.64

SALE

~~SGD$9.30~~ SGD$5.58

SALE

~~SGD$9.30~~ SGD$5.58

Original replacement parts for TRP V2 comprising of a middle plate - lighter version. Compatibility : TRP V2, KATAK Stretch SE Specifications: Material 2mm high performance Mitsubishi carbon fibre Package 1 x middle plate

SGD$19.08

Total Rotor Performance (TRP) upgrade parts are designed specifically for FPV Pilots who wants the last bit of performance from their frames. We do listened - these Version 2 arms are redesigned for increased durability yet no weight penalty when compared to the Version 1 arms, in fact there are some weight saved. TRP Racing Arms on a KATAK Stretch SE frame's will see a...

SALE

~~SGD$18.30~~ SGD$10.98

Total Rotor Performance (TRP) upgrade parts are designed specifically for FPV Pilots who wants the last bit of performance from their frames. With the TRP Side Plates, the KATAK takes on an aggressive sleek profile for that ultimate racer look without losing the signature "front" of the KATAK. When fitted along with the TRP V2 Racing Arms, TRP V2...

SALE

~~SGD$4.10~~ SGD$2.46

Sold Out

Lighter. Faster. Sleeker Presenting to you the new TRP SPRINT – an FPV racing frame designed and produced by Total Rotor Performance© We’ve heard you – crafted from the same high quality Mitsubishi carbon fibre plates of the original TRP, the new TRP SPRINT improves on several fronts including weight, durability, ease of build and overall flight performance; all while maintaining the proven design approach of its...

SALE

Sold Out

TRP review TRP flight video Designed and produced in Singapore, the TRP V2 by Total Rotor Performance© is based on the proven 5” KATAK Stretch SE platform and yet distinctly different. Designed for the discerning FPV pilot, the TRP V2 has pulled those extra bits to help pilots achieve even higher racing performance at an amazing price and quality of finish. Crafted from high performance Mitsubishi carbon...

TPU Battery Protector / Landing Gear

SGD$2.85

Light weight TPU 3D printed designed for racing frames with bottom mounted batteries, it protects the battery from ground hits when in low level flights or when landing. Specifications : Material 3D printed TPU Colour Yellow, Red Front Incline Angle 30 degrees Fit Type 1 - Red (200 - 250mm frame) Type 2 - Yellow (110 - 130mm frame)...

TurboBee RS V2 Frame Kit (120RS or 136RS)

SGD$19.80

The TurboBee micro FPV racing is available in two ultra-light frame size, 120 or 136mm, for all-up-weight that is below 200g. Designed for micro drone flying with the speed and performance of a 5" frame Specifications : Frame Number TurboBee RS V2 120 TurboBee RS V2 136 Wheelbase 120mm 136mm Bottom Plate 3mm 3mm Canopy Blue TPU Blue TPU Dimension 120mm*120mm*30mm 136mm*136mm*30mm Weight 13.5g 17g...

Universal Micro FPV Camera Adapter

SGD$1.55

These adapters enables you to mount of a 19mm wide micro sized camera on any standard 28mm wide frame, saving as much as 10grams. Use the standard screws that came with your micro camera to mount the adapters to your camera and the included countersunk screw and nut to connect to your frame. Specifications: Material TPU Colour Red Weight 2g...

Vertigo VX2 Vertical FPV Racing Frame Kit

SGD$25.56

The Vertigo is a symmetrical-X frame is designed to be the ultimate micro racing quad, fast and durable, with the unique vertical arm design reducing drag to an absolute minimum. Aluminium arms mounts makes for fast arm change with the aluminium torsion brace providing frame rigidity for enhanced flight performance and durability. The frame design allows for either top mounted or bottom slung...

WS2812B LEDs light for flight controller

SGD$1.05

Available in 2 or 4 LEDs version, these mini size LEDs board provide that extra enhancement for your racing drone, connected to LEDs pad which are available on most flight controllers. The LED can be configured through Betaflight of Cleanflight configurators, it can be set for craft orientation, system warnings, arm status, turn indication, lason scanner effect etc Specifications:...

SALE

XING 1204 FPV Micro Motor - 4500kv

~~SGD$19.50~~ SGD$14.63

iFlight XING series motors, designed by FPV pilot and specialist Patrick Xing; combining iFlight's high-quality motor production technology with Patrick Xing's technical expertise to produce a top-of-the-line motor. Super durable with an ultra-light Unibody bell, this motor weighs a mere 6g ensuring that your flight performance is never compromised by any extra weight. Suitable Replacement part for iFlight Alpha Whoop...

XING-E 1104 Race Motor - 4200KV

Sold Out

iFlight XING series motors, designed by FPV pilot and specialist Patrick Xing; combining iFlight's high-quality motor production technology with Patrick Xing's technical expertise to produce a top-of-the-line motor. Super durable and ultra-light, these 1104 motors only weigh 5g with 60mm (4200KV) / 44mm (8300KV) cable. Features: * XING-E 1104 brushless motors are customized for 2~3S brushless whoop drone * Shaft...

XT60 Female To XT30 Male adapter

Sold Out

XT60H Battery Connector Kit

Sold Out

Quality AMASS XT60H battery connectors come pre-soldered with 12AWG gauge soft silicone for direct connection to flight controllers, BEC or 4-in-1 ESC. The sheath at the solder connection provides strain relief for the solder joints and added protection against shorts from damaged insulation near the solder joints that may damage your LiPo batteries. Specifications: Connector AMASS XT60H male with connector sheath Connector Material...

Products

Recently Viewed